Unistruct Solar Stand C Channel Roll Forming Machine
1. Standard Size: 21*21, 41*21, 41*25, 41*41, 41*52, 41*62, 41*72, 41*82 or as per your requirement
2. Standard Thickness: 1.0mm, 1.5mm, 1.6mm, 2mm, 2.5mm, 2.75mm, 3mm or as per your requirement
3. Standard Length: 2440mm, 3000mm, 5800mm, 6000mm or as per your requirement
4. Surface:
Hot-dip galvanized strut channel
Pre-galvanized strut channel
Powder coated strut channel
Electro Galvanized strut channel
5. Peforated: 14*28mm, 11*25mm, 25*30mm, or as your requirements
Equipment part list of automatic U type auto punching/roll forming machine
| No. | Name | Type | Quant. | Power of motor (KW) |
| 1 | Passive Decoiler | MT-300 | 1 set | |
| 2 | Leveler | HS-300 | 1 set | 3 |
| 3 | Servo-feeder | NCF-300 | 1 set | 2.2 |
| 4 | JF21-80 Punching machine | YANGLI GROUP | 1 set | 7.5 |
| 5 | Punching mould | | 1 set | |
| 6 | Roll forming machine | Gantry gearbox | 1 set | 18.5X2 |
| 7 | Flying Hydraulic cutting | | 1 set | 5.5 |
| 8 | Run-out table | SL-300X4000 | 1 set | |
| 9 | Electric control system | | 1 set | |
Main technical parameters
1. Machine Technical parameters
Width of material sheet:≤200 mm
Thickness of material sheet: 0,95 mm up to 1,55 mm
Material of sheet:Galvanized Steel,etc
Line production speed:15-20m/min(including punching/forming/cutting)
Length of the work piece:3000mm-6000mm.
Total Power: 48.2 KW.
2. Machine General Working Condition
Area of production line: length45m x width 3.5m x height 5m
Feeding direction: from left side to right side
Power: 380V, 50Hz, 3 phase
Pneumatic station: pressure 0-0.6MPa.,0.5m3/min.
Hydraulic oil: 46# Hydraulic oil
Gear oil: 18# gear oil
Composition of whole line
1. decoiler
a. Width of material: 300mm
b. Inner hole diameter of coil: 400-460mm
c. Maximum diameter of coil: 1600mm
d. Loading weight : 3000kgs
e. Manual expanding core
f. No power transmit, with brake device
2. Straightening machine
a. Width of feeding: 300mm
b. Thickness of material: 2.5mm
c. Quantity of straighten roller: 9 pcs
d. Quantity of pinch roller: 2pcs
e. Diameter of shaft: 80mm
f. Thickness of roller: 40Gr steel (temper rigidity: HRC25-27)
g. Motor: 3KW
h. Speed: 8m/min
i. Transmit: chain and wheel
3. Feeder
a. Width of material: 300mm
b. Thickness of material: 2.5mm
c. Quantity of roller: 4 pcs
d. Material of roller: GCr15 steel
e. Rigidity of roller: HRC55-57
f. Servo motor: 0.85KW (Mitsubishi)
g. Speed: 0-10m/min
h. Transmit: wheel
4. Roll Forming machine
a. Groups of roller: 18 nos (change 7 groups roll for another height)
b. Material of roller : Gr15 steel and Cr12MOV
c. Hot treatment of roller; HRC55°-57°
d. Surface of roller: polishing treatment
e. Diameter of main shaft: 60mm, material: 45# steel
f. Bearing of roller: 60310
g. Thickness of side wall: 30mm
h. Transmit; chain and wheel
i. Motor; 15 KW, 400 speed reducer
j. Machine frame: welded by steel pipe
k. Equip cooling water pump device
l. Speed; 2-8 m/min
5. Cut-off
a. Oil pressure station: 1pcs
b. Motor: 3KW
c. Cut-off mould: 1 set ( with scrap cut-off)
d. Material of cut-off mould: Gr12 steel
e. Rigidity: HRC60-62
f. Cut-off work pressure: 15T
4.Main Machine Technical parameter
| ,NO. | Name | unit | parameter | remark |
1 | materials | Type | | Mild steel galvanized sheet | |
| Plate strength | | ≥350 | |
| Plate thickness | mm | 1.5~2.5 | |
| 2 | specification | mm |
See the picture | |
| 3 | speed | m/min | 6~8 | |
| 4 | Material of the roller | | GCr15 Hardening treatment | |
| 5 | drive type | | Gear box | |
| 6 | power | kw | About40 | |
| 7 | Electrical control system | | PCL frequency control | |
| 8 | Size(lengthXwidthXheight) | m | 35X4X3.9 | |
Product Tags:
|
|
41*62 C Channel Roll Forming Machine , 48.2 KW Purlin Forming Machine Durable Images
|
